Number of control axes

Maximum number of control axes: 5 axes (optional 6 axes)

Number of PLC control axes: 5 axes

Maximum number of linkage axes: 5 axes (linear interpolation), 3 axes (spiral interpolation), 2 axes (arc interpolation)

Coordinate value (system) and size

Local coordinate system, machine tool coordinate system and workpiece coordinate system 1-6 (g54 ~ G59)

Coordinate plane selection

Position command range: ± 9999999 × Minimum input unit

Absolute / incremental programming, English / metric conversion, linear axis / rotary axis

Preparation function

85 g instructions, including fast positioning, interpolation, automatic chamfering, tool compensation, metric and British system input, coordinate rotation, scaling, mirroring, sentence macro instructions, macro program call, jump, cycle instructions, small segment forward-looking, etc

Feed function

Fast moving speed: 0mmmn ~ 100000mm / min

Fast magnification: F0, 25%, 50% and 100% four levels of real-time adjustment

Cutting feed rate: 0mm / min ~ 15000 mm / min

Feed rate: 0 ~ 150%, 16 levels in total, real-time adjustment

Bus function

Servo motor adapted to multi turn absolute position encoder

The absolute coordinate system is automatically restored after the machine tool is powered off

Mechanical zero return of machine tool without stop

Online modification of servo parameters

Servo status online diagnosis

Operation log

Remote monitoring and fault diagnosis function

Spindle function

Spindle speed: it can be given by s code or PLC signal, and the speed range is orpm ~ 9999rpm

Spindle magnification: 50% ~ 120%, a total of 8 levels of real-time repair and adjustment

2 channels of 0 ∨ ~ 10V analog voltage output

Support analog spindle m-shift and τ Type shift function, flexible tapping / rigid tapping

2-way spindle encoder feedback, the number of spindle encoder lines can be set  (0 or 100p / R ~ 5000P / R)

Tool function

Tool length compensation (tool offset): 32 groups

Tool wear compensation: 32 groups

Tip radius compensation (type C)

PLC function

Two level PLC program, 5000 steps at most, and the refresh cycle of level 1 program is 8ms

13 basic commands and 31 functional commands

PLC program online display and real-time monitoring; Support PLC warning and PLC alarm

Basic I / O: 48 inputs / 38 outputs

Expandable serial I / O unit (optional): or-44t: 48 point input, 32 point output, 4-channel analog voltage output

Auxiliary function

Special m codes (M00, M01, M02, M30, M98, M99), and other m codes are defined by PLC

Program storage and editing

Program capacity: 64M, 10000 programs (including subroutines and macro programs)

Editing method: full screen editing

Editing functions: program segment word retrieval, modification, deletion, copy and paste

MDI allows you to input and run 8 program segments

Support macro program / subroutine calling, and allow 4-fold subroutine nesting

Calculator, online programming wizard, online drilling cam function, automatic programming function of plane milling

Program check function

Track preview, graphic simulation, idle operation, machine tool lock, auxiliary function lock, single section operation

Simplify programming functions

Fixed cycle, compound cycle, drilling cycle, rigid tapping, automatic chamfering, sentence macro instruction programming, indexing function of indexing table

Compensation function

Reverse clearance compensation: 0mm ~ 2mm (or 0 inch ~ 0.2inch). The reverse clearance compensation mode and frequency are set by parameters

Memory pitch error compensation: a total of 1024 compensation points, and the number of compensation points of each axis is set

interface

Support Chinese, English, Russian and other languages

The processing track is displayed, and the processing track is enlarged, reduced, translated and the viewing angle is switched in real time

Position, program, tool compensation, alarm, parameter, setting, graphics, diagnosis, ladder diagram

Communication function

USB: ∪ disk file operation, ∪ disk file direct processing, support PLC program and system software ∪ disk upgrade

RS232: bidirectional transmission of part programs, parameters and other files, supporting PLC program update

LAN: remote file transfer

Electrical grounding

48 / 38 point digital input / output interface, 2-way encoder interface, 2-way handwheel interface, 2-way spindle analog interface, RJ45 network port and gskl Ⅰ NK network port

Safety function

Emergency stop, hardware travel limit, software travel check, data backup and recovery